Holybro Kakute F7 HDV Flight Controller Tekko32 F3 HDV 40A 3-6S Blheli_32 4 In 1 Brushless ESC

Banggood
Score du Deal0
68.03€ Voir l'offre
BGKAKUF7HDV
Score du Deal0
68.03€ Voir l'offre
BGKAKUF7HDV

Découvrez le Holybro Kakute F7 HDV Flight Controller Tekko32 F3 HDV 40A 3-6S Blheli_32 4 In 1 Brushless ESC en promotion :

Holybro Kakute F7 HDV Flight Controller Tekko32 F3 HDV 40A 3-6S Blheli_32 4 In 1 Brushless ESC

    Overview
    HolyBro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect HolyBro Kakute F7 HDV to the DJI FPV VTx, for both signal and power.

    New BLHELI32 ESC with F3 MCU, give more smooth control and faster 
    responding speed. Supports up to 55A burst and 40A continued.
     
    Specifications:
    Kakute F7 HDV Flight Controller MCU: STM32F745 32-bit processorIMU:PMU6000Barometer: BMP280USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)6 hardware UARTS (UART1,2,3,4,6,7)All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.TF card for Blackbox loggingDimensions: 35x35mmMounting Holes: Standard 30.5mm square to center of holesWeight: 8g
    Tekko32 F3 HDV 40A ESC
    32bit ESC with BLHELI32 firmware
    Supports 3-6S lipo input
    PWM input, TLM supported
    Voltage output (VBAT)
    NO BEC
    Supports oneshot / Multishot / Dshot PWM
    Mounting holes 30.5×30.5mm
    Supports damped light
    F3 MCU, runs double faster than F051
    Extra Cap needed for high current or 6s usage
    Dimensions: 44x37x6mm
    Weight: 11.6g


     
    Features:
    • Supports Betaflight, Butterflight, and Cleanflight.• High-performance / low-noise IMU. MPU6000 with 6-axis gyro and accelerometer. • Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA for use with external GPS/magnetometer units.• Dedicated bootloader button for easy firmware flashing.• Low-profile design fits into even very compact frames.• Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).• Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the KAKUTE F7 HDV monitors voltage directly from the power supply.• Filtered voltage output for clean, noise-free video. 2 On-board regulators output 5V and 8V. 5V output up to 1.5A to power peripherals such as receiver, FPV camera, or LED strip. 8V output up to 2A to DJI FPV VTx.• Supports BLHeli pass-through for easy ESC upgrade and configuration.

    Package Included:
    1 x Kakute F7 HDV Flight Controller 
    1 x Tekko32 F3 HDV 40A Brushless ESC

    1 x Electrolytic capacito: 1000uF 35v
    1 x 8pin to 8pin 1mm pitch 65mm cable 
    1 x 8pin to 8pin 1mm pitch 25mm cable 

     

    Obtenez plus d’informations sur  le Holybro Kakute F7 HDV Flight Controller Tekko32 F3 HDV 40A 3-6S Blheli_32 4 In 1 Brushless ESC  chez notre partenaire.

    N’oubliez pas d’utiliser le coupon de réduction indiqué en haut de cette page avant de passer commande.

    Nous serions heureux de connaître votre avis

    Laisser un commentaire

    Ce site utilise Akismet pour réduire les indésirables. En savoir plus sur comment les données de vos commentaires sont utilisées.